Pick A Toilet may collect a share of sales or other compensation from the links on this page.
Last Updated on August 6, 2022 by acechapman
Usually, toilets are installed on the floor. These toilets are mounted on the floor because the waste pipe runs through it, and the water supply pipe is from the wall. A floor toilet is a great option. It does have its downsides.
They can also accumulate gunk at the grout joints that come in direct contact with the floor. This wouldn’t be the case with wall-hung toilets. They are completely supported by the wall and don’t touch any floor.
If you are tired of cleaning the floor joints, it is time to replace your toilets with wall-mounted ones. We’ve created a step-by-step guide that will help you install a wall-hung toilet like a pro.
Wall Hung Toilet Installation
Turn off the water supply before you start the installation. Next, remove your old toilet. Drain the tank then remove the connector. Next, use a hammer with a chisel to break the grout that holds the toilet to the ground. The waste pipe must be moved after that. Then, seal the hole in the floor.
Assemble Your Mounting Frame
Assemble the frame that will house the toilet tank. As per the instructions in the manual, join the bars to form the frame. Install the brackets and flush pipe for the tank. Mount the tank onto the frame.
To fix all fasteners, use a small torque wrench. Next, secure the waste pipe with the plastic clamp and metal feet.
Mark The Wall And Floor
Begin by drawing a 1.08 m vertical line on the wall, starting from the floor. The line should be parallel to the middle of the waste pipe. Draw the lines in a perpendicular manner at 1.08m(2nd line) and 1m(3rd line). Next, mark the third line with two lines 235 mm each to the right or left of the vertical.
The frame should be placed so that the 90-degree elbow from the waste pipe can be inserted into the clamp. Mark the points where the mounting holes of your frame touch the floor. Next, remove the mounting frame.
Before you proceed to the next step, ensure that there is a minimum distance of 230 mm between the wall and the frame.
Install The Mounting Frame
Use a 10-mm drill bit to drill holes in the floor and wall. Next, insert the plastic anchors into the holes. Place the mounting frame on the floor with its metal feet. Attach the frame to the floor using screws.
Attach the threaded bar to the top of the frame and mounting brackets. Next, attach the mounting brackets to your wall using screws. Turn the threaded rod to align the frame vertically. While doing this, use a bubble level.
Install The Flush System
Remove the red plastic handle from the tank. Next, take off the plastic cover that covers the water connections. Install a stop valve at the water outlet from the wall. The stop valve output should point to the right. To prevent leakage, make sure you apply enough Teflon tape on the thread.
Attach a flexible hose to the stop valve’s output. Next, close the stop valve. Check that the water supply to the bathroom is on and that there are no leaks. To check the water pressure, place the free end of your hose in a bucket. Close the valve.
Connect the free end to the water input thread on the flush mechanism. Finally, attach the inspection shaft. You will need to remove the inspection shaft if the flushing mechanism fails in the future.
Install The Drywall
You can cover the top, sides, and front of the mounting frame with drywall. Cut the drywall exactly where the toilet fittings will be installed.
Install The Wall Hung Toilet
Join the flush pipe to its seal. Next, insert the flush pipe into the toilet bowl. Mark the end of the pipe that protrudes from the bowl with a pencil. Then, insert the flush tube into the flush unit. Mark the location where the flush pipe protrudes from the flush unit with a marker.
Take the length of the pipe from the pipe’s edge to each mark. Add 5 millimeters to the sum of both lengths. Cut the flush pipe to this length. Next, smoothen the edges of the pipe with a piece of sandpaper. Then, place the flush pipe in the flush unit.
Attach the threaded rods supporting the toilet bowl to its mounting frame. The rods should extend 6 cm beyond the frame. Install the toilet bowl by inserting the threaded rods into the mounting holes. To fix the toilet, use washers and nuts. Use a bubble level to verify that the top of your bowl is horizontal.
Install The Flush Plate
Cut the plastic covering of the flush plate with a utility knife. Install the mounting bracket for the flush plate onto the drywall. Connect the blue hose to the flush unit and attach the air button to the plate.
Next, open the stop valve and place the flush plate on the mounting bracket.
To verify that the toilet is working, press the air button. Fill the bowl with silicone sealant if everything seems to be in order. Install the toilet seal.
Wall Hung toilets can be an attractive alternative to regular toilets, as you can see. They are easy to clean and won’t collect too much gunk. Installing them can be difficult. However, you don’t have to be concerned if you follow these instructions. Otherwise, you can hire plumbing professionals to install the wall-hung toilet for you. Although, this can be a bit costly.